The following steps cover the Latch Hub scoping and installation process. If you have any questions along the way, please contact support@latch.com.

We first recommend reviewing the Latch Hub Installation Guide (linked here).

Scoping Requirements:

1. The property ideally should have a building-wide Network that will supply a constant internet source for use with Hubs
   • In the case that a building-wide network does not exist, the Channel Partner will need to assess the site to verify if Cellular is a viable full-building solution
   • A Twilio SIM card should be used in a supported device (smartphone, etc) to validate that when internet speed tests are run on the device throughout all parts of the building, the test results need to have a minimum of 10 Mbps download speed. 
   • If the speeds are slower than 10 Mbps, cellular should not be used at the property

Installation:

1. Find an appropriate location for the Hub.
   • The Hub must be placed within 30 feet (about 12 paces) of the lock and have a clear line of sight (e.g. ideally not blocked by walls or doors). For best performance and to ensure performance, please place the Hub within 20 feet (8 paces) of the lock.
   • For Smart Home installations (when light switches, leak detectors, or thermostats are included) the Hub must be installed inside the apartment and be dedicated to a singular Unit. Note: We do not support hallway installs when managing personal smart devices for privacy reasons.
   • For Access installations (only updating our locks), the Hub can be installed in a hallway. The hub can update a maximum of 4 locks and should be installed within the distance and line of sight guidelines listed above.
2. Plug the AC adaptor into the back of the Hub and into the wall outlet.
3. Confirm the LED on the top of the Hub starts blinking white.
4. Connect the Hub to the internet.
   • With the current version of the Hub, ethernet or cellular is required to set up WiFi. If the building provides WiFi then an installer can provision the hub from anywhere in the building with an ethernet port or cellular signal and wifi coverage.
     • Ethernet: Plug one end of the ethernet cord into the back of Hub and the other end into the router or modem.
     • Cellular: The SIM card should be activated and no further action is required. Please contact Latch Support if you have not activated the Hub’s sim card.
     • Wi-Fi: Confirm either ethernet or cellular is available so that the hub can receive the network and password through Manager App. The Hub must be added to the property while on Ethernet or Cellular to enable WiFi via the Manager App.
       • • Select the Hub in the Manager App.
         • Tap 'Configure.'
         • Tap 'WiFi Setting' and select 'WiFi Enabled.'
         • Select the WiFi network, enter the network password, and tap 'Join.'
5. Open Latch Manager App and enter the Hub’s serial number by tapping the plus sign “+” symbol in the upper right corner.
6. Once the Hub has been connected to the internet, confirm the LED displays solid white.
7. Tap 'Edit Unit' and assign the Hub to a unit, if applicable.
8. The Hub is now ready to pair with smart devices.

If a Latch Hub will not connect to the Internet, is showing a solid white LED at set up, or has disconnected from the internet and will not reconnect, we recommend running through the following steps:

1. First, check that the Hub is plugged into a working power outlet with the supported power adapter. You may have trouble attempting to set up the Latch Hub while it is running on the integrated backup battery.
2. Second, check that the Hub has a reliable internet connection available for connecting with Latch.
• For Ethernet connections: Ensure that the Hub has access to a known working ethernet connection. Test that the ethernet port and cable are working properly by plugging them into another device such as a laptop and see if the other device connects to the internet. Make sure that the green status led located inside the ethernet port on the back of the Latch Hub blinks occasionally, which indicates the ethernet cable is properly attached.
• For Cellular connections: Hubs must have their cellular capability enabled by Latch before they can utilize it for internet connectivity. Make sure you contacted Latch to enable cellular before attempting to use it for connectivity. We recommend using Ethernet or WiFi as the main internet connectivity for the Hub. It’s important to keep in mind that if you intend for the Hub to use Cellular as the main connection type, you take into account signal strength. The Hub requires a minimum of 10 Mbps of download speed for expected functionality. The quality of the cellular network and the location of the Hub and any nearby interference will impact the ability of the Hub to establish a reliable internet connection using cellular. You can connect the Hub to Ethernet to test that it successfully connects to Latch and displays a solid white LED. If the Hub can connect using Ethernet, it’s possible that the cellular connection is not stable or has not been enabled.
• For WiFi: Check that the WiFi network that the Hub should be connected to is broadcasting and can be connected to using another device. It is helpful to test that a device such as a smartphone or tablet can connect to the network from the location of the Hub. If the WiFi network is working correctly for other devices, reconnect the Hub to WiFi using the below steps.

Reconnect the Hub to WiFi:

1. Open the Latch Manager App.
2. Select the Property where the Hub is installed.
3. Choose the Smart Devices tab, search for the Hub in the list, and tap on it.
4. Tap 'Configure.'
5. Tap on the desired Network Name under Available Networks.
6. Enter the Network Password and tap 'Join.'
7. Check that the Hub successfully reconnects and displays a solid white LED.

Latch Hub Spec Sheet